FAQ for Pilotfly Action-1
![Simplebgc Gui For Mac Simplebgc Gui For Mac](/uploads/1/1/8/2/118229910/952745346.jpg)
SimpleBGC 32-bit v3.x GUI GUI 2.60b4 — latest version Previous versions SimpleBGC 8-bit Downloads Mobile App iOS App Android App Encoders with SimpleBGC 32-bit. Runing SimpleBGCGUI for Mac OSX. Dustlessimage October 2013. About SimpleBGCGUI for MAC OSX dustlessimage October 2013. Bencio February 2015. MAC OS users: GUI uses a serial communication, that needs to create a lock file. To allow it, you should to do the following steps. Just to make sure, you are starting the SimpleBGCGUI.jar, i.e. Not running the SimpleBGCGUI.exe on Parallels etc. Sawprod February 2014. Im having the same problem. GUI (Windows, macOS, Linux): SimpleBGCGUI240b8.zip (5Mb ) Upper limit for PID values was increased to 255 (2.55 for I) Upper limit for RC speed was increased to 255 and its effect was decreased 4x times to get finer step in adjustment. To connect to your Gimbal from a Mac or PC Computer, you must first download the proper software. If you are on a MAC computer, you will also need to download drivers. Advanced TAB SimpleBGC GUI v2.43 b9 for CAMETV 7800 Gimbal.
- Can I remotely control my Pilotfly product?
--> All Pilotfly products are equipped with a Bluetooth module which gives you the ability to control your gimbal via an Android App. For further informations refer to the instruction manual. - Where can I get the latest SimpleBGC Software?
--> The latest version of the SimpleBGC software can be downloaded with the following link: SimpleBGC_GUI_2_62bx.zip . Apart from this you might need an additional USB to UART Driver which can be downloaded here: http://www.silabs.com/products/mcu/pages/usbtouartbridgevcpdrivers.aspx - How can I check which firmware version my device currently has?
--> Please establish a connection with the SimpleBGC software and your Gimbal via Bluetooth or USB cable. Go to the tab 'upgrade' and press the 'Check' button to verify your firmware version and to check for new versions. The actual released firmware for Pilotfly gimbals is 2.62b3.
Simplebgc Gui For Mac High Sierra
- Where can gather more information about the SimpleBGC Software?
--> The SimpleBGC user manual can be downloaded here.
- How can I activate or use the invert mode?
--> All Pilotfly products are capable to detect automatically the invert mode. Just turn the handle around while the gimbal is powered off and turn it on again. The gimbal detects automatically the invert mode and you are ready to go. All other profiles which can be selected via the Mode-button are working in the invert mode as well.
Downloads For 32-bit Boards : BaseCam Electronics
Possible failures and solutions:
See Full List On Basecamelectronics.com
Roll motor is not horizontal levelled | Please make a Gyro & ACC calibration described in the user manual. |
The system starts vibrating while moving the gimbal 90° forward (brief case position) | Figure out which motor is causing the vibrations, in this case it is most likely caused by the Pitch motor. If so decrease the D-value of the Pitch slightly or change Motor power value of Pitch. |
Pitch motor is suddenly missing steps while moving up or down. | Ensure proper balancing of the camera. Increase motor power of Pitch motor. |
System starts vibrating while moving | Figure out which motor is causing the vibrations, and decrease the D-value of the related axes or change Motor power value of related axes. |
System is slightly drifting on the yaw axis. | Poor Gyro calibration of Frame IMU. Frame IMU needs to be re-calibrated. Note: Frame IMU must be calibrated via SimpleBGC Software installed on your PC, MAC or Android App (SimpleBGC32) |
While moving forward (brief case position) roll axis keeps not straight and is moving slightly to left or right. | Poor ACC & Gyro calibration of Camera IMU. Please make a Gyro & ACC calibration described in the user manual. |
System is flattering in each direction. | Wrong Motor setup. Hold the gimbal steady and start “Auto” for the Motors in the Basic Tab of SimpleBGC GUI. Ensure that all motor poles are set to “14”. After that perform a calibration for Camera and Frame IMU sensors. Logic pro x download for mac free. Try Logic Pro X free for 90 days. Get a free trial of Logic Pro version 10.5.1 for your Mac. Video: https://youtu.be/vOEP65UFV9w |
System starts beeping continuously. | Check battery level. Battery might be exhausted. Charge battery or connect the external battery. |
System starts beeping and battery is fully charged. | Check battery level in the SimpleBGC GUI on the right bottom corner. Gnupg mac mail. Battery calibration might be necessary. Please follow the instruction for battery calibration. |
Roll and pitch not in level even after ACC & Gyro calibration | Verify in the RC –Tab of the SimpleBGC GUI the “Initial angle” of each axes. Initial angle need to be set to “0”. Note: Operations like “Set tilt angles by hands”, “Swap RC Roll-Yaw” or “Swap RC Pitch – Roll” will save their angles to this field, too. |